Plastic Tubing Clamps are durable and will not rust or corrode. Select from 3 sizes for best tubing fit.
ā¢ Mini Tube Clamp with single position on/off gives positive shut-off with fingertip control; use for thin-walled tubing under 4.7mm (Ā³āāā") O.D.
ā¢ Mid-Range Tube Clamp has a 15-position steppe..
Plastic Tubing Clamps are durable and will not rust or corrode. Select from 3 sizes for best tubing fit.
ā¢ Mini Tube Clamp with single position on/off gives positive shut-off with fingertip control; use for thin-walled tubing under 4.7mm (Ā³āāā") O.D.
ā¢ Mid-Range Tube Clamp has a 15-position steppe..
Suspend dialysis bags in large beakers or pitchers up to 0.63cm (Ā¼") thick with these strong clips.
ā¢ Bags slide easily into the slot and then the holder can be clipped onto the containerās edge
ā¢ Smooth polypropylene surface may be marked with identifying sequence numbers
Autoclavable..
Plastic Tubing Clamps are durable and will not rust or corrode. Select from 3 sizes for best tubing fit.
ā¢ Mini Tube Clamp with single position on/off gives positive shut-off with fingertip control; use for thin-walled tubing under 4.7mm (Ā³āāā") O.D. ā¢ Mid-Range Tube Clamp has a 15-position stepped ..
Side opening tube clamp permits installation onto tubing without disconnecting from apparatus or interrupting operation.
ā¢ Constructed of durable nylon for long life and good chemical resistance
ā¢ Accepts any tubing up to 6.4mm (1/4") O.D..
Tube clamp is molded of strong, durable plastic with serrated jaws 2.7cm (1Ā¹āāā") long. Attach at any point on tubing without disconnecting tubing.ā¢ Operate with one hand; locks closed and opens when the locking tab is released
ā¢ Fits tubing up to 1.3cm (Ā½") O.D.; wall thickness of 0.82mm (1/32") or..
Non-corroding clamps hold burettes firmly in place. ā¢ Soft rubber pads hold burette without scratching
ā¢ Clamp fits standard 12.5mm (Ā½") support rod and includes an adapter to fit to narrower 9.5mm (ā ") rod (support rod not included)
ā¢ Made of chemical resistant polypropylene; autoclavable at..
Non-corroding clamps hold burettes firmly in place.
ā¢ Soft rubber pads hold burette without scratching
ā¢ Clamp fits standard 12.5mm (Ā½") support rod and includes an adapter to fit to narrower 9.5mm (ā ") rod (support rod not included)
ā¢ Made of chemical resistant polypropylene; autoclavable at 121Ā°..
Offers on/off and fine control so accurate that it replaces stopcocks in many applications. ā¢ Can be installed without disconnecting tubing or interrupting operation
ā¢ Accepts flexible tubing up to 14mm (Ā½") O.Dā¢ Molded of Acetal plastic; autoclavableā¢ Resistant to acids, alkalis and organic solvent..
Firmly holds test-tubes, burettes and other labware in placeā¢ Spring aciton, stainless steel jaws have a flat wing-head screw for tighteningā¢ Jaws are covered with rubber tubing for increased friction and a soft gripā¢ Opening range of 0 to 25mm (1")ā¢ Overall clamp length: 22cm (9")..
This open-sided stainless steel bosshead clamp accepts rods up to 13mm (Ā½") diameter.
ā¢ Holds rods at right angles to one another
ā¢ Secures rods with flat wing-head clamping screws..